導讀：閥門電動執行器的電動執行器帶有極限終點限位開關，到終點能自動切斷電路，同時為了保障工程安全，閥門電動執行器設有電力過載保護裝置和信號燈指示。
Introduction:The electric actuator of the valve electric actuator has the limit terminal limit switch, which can automatically cut off the circuit at the end. In order to ensure the safety of the project, the valve electric actuator is equipped with electric overload protection device and signal light indicator.

閥門電動執行器的故障分析
Failure analysis of valve electric actuator

閥門電動執行器安裝現場圖
Field diagram of valve electric actuator installation

閥門電動執行器可以分為電動對夾式蝶閥和電動法蘭式蝶閥，該類閥門是依靠電動執行器的電機工作，帶動蝶閥的閥軸轉動，閥軸又帶動蝶板旋轉90°來實現閥門的啟閉，可以做截斷和調節流量使用。閥門電動執行器的電動執行器帶有極限終點限位開關，到終點能自動切斷電路，同時為了保障工程安全，閥門電動執行器設有電力過載保護裝置和信號燈指示。本文介紹閥門電動執行器可能出現的故障以及對應的解決方法。
The valve electric actuator can be divided into electric pair clip butterfly valve and electric flange butterfly valve. This type of valve is based on electric actuator's motor to work, drives the valve shaft of butterfly valve to rotate, and the valve shaft drives the butterfly plate to rotate 90 degrees to realize the valve opening and closing, and can be truncated and adjusted the flow.The electric actuator of the valve electric actuator has the limit terminal limit switch, which can automatically cut off the circuit at the end. In order to ensure the safety of the project, the valve electric actuator is equipped with electric overload protection device and signal light indicator.This paper introduces the possible faults of valve electric actuator and the corresponding solutions.

故障1.閥門電動執行器閥門填料處外漏
Fault 1. leakage at the filling of the valve of the valve electric actuator
發生此類故障的原因有：①填料老化嚴重。②壓蓋螺栓沒有擰緊或出現松動。
解決方法：①更換新的填料。②均勻的擰緊壓蓋螺栓。
The causes of such failures are:①The serious aging of fillers.② The gland bolt are not tightened or loosened.
Solutions:①using renewal fillers.②Tighten the cap bolt evenly.
故障2.端蓋出現滲漏
Fault 2.Leakage of end cover
發生此類故障的原因有：①螺栓未擰緊。②O型圈損壞。
the causes of such failures are:(1) the bolt is not tightened. (2) O type ring is damaged.
解決方法：①檢查螺栓是否松動，將其擰緊。②更換新的O型圈。
Solutions:①Check the loosening of the bolt and tighten it. ②use renewal O type ring.
故障3.密封面發生滲漏
Fault 3. Leakage of sealing surface
發生此類故障的原因有：①蝶板關閉不到位。②密封面存積污垢，導致關閉不嚴。③密封面損傷。
The causes of such failures are: ①the closure of the sphenoid plate is not in place. ②The sealing surface deposited dirt, which resulted in the lax closure. ③ the damage of the sealing surface.
解決方法：①調整閥門電動執行器電動執行機構上的螺釘，將蝶板關閉到位。②清理密封面的存積污垢。③修補損傷的密封面。
Solutions:①adjust the screws on the electric actuator of the valve electric actuator and close the butterfly plate. ②Clean up the deposit and dirt of the sealing surface. ③ repair the damagedseal surface.
故障4.電動裝置運轉不靈活導致閥門不能正常啟閉
Fault 4.The operation of the electric device is not flexible, resulting in the valve can not normally open and close.

發生此類故障的原因有：①填料壓的過緊。②填料的壓蓋沒有緊固到位，發生傾斜。③過度裝置故障損壞。
The causes of such failures are:① the packing pressure is too tight.② The gland of the packing is not fastened in place and tilted. ③ fault damage of the overdevice.

解決方法：①填料壓蓋不要壓得過緊，適當放松。②校正填料壓蓋的垂直度。③更換新的過渡裝置。
Solutions:① Packing gland should not be pressed too tightly, shoulid relax properly. ②Correct the perpendicularity of the packing gland. ③use renewal transition device.
故障5.啟閉到頭了電機沒?；蛘邌㈤]不*
Fault 5.The motor does not stop or the start and close are not complete
發生此類故障的原因有：①極限開關失靈了或者是過載保護裝置不準。②極限開關動作過早或反應太遲。
The causes of such failures are:①The limit switch is out of order, or the overload protection device is not allowed. ②The limit switch works too early or too late.
解決方法：①更換極限開關或者對過載裝置做調整，保證度。②調整極限開關的反應速度。
Solutions:①use renewal limit switch or adjust the overload device to ensure accuracy. ②Adjust the reaction speed of the limit switch.