北京北廣精儀儀器設備有限公司
北京北廣精儀儀器設備有限公司
暫無信息 |
絕緣環氧樹脂、塑料橡膠體積表面電阻率測試儀
絕緣環氧樹脂、塑料橡膠體積表面電阻率測試儀使用條件
①環境溫度： 0～40℃
②相對溫度：≤70%
③供電電流：交流 220V±10%50Hz
絕緣環氧樹脂、塑料橡膠體積表面電阻率測試儀主要標準：
GB/T 1410-2006 固體絕緣材料 體積電阻率和表面電阻率試驗方法
GB1672-8液體增塑劑體積電阻率的測定
GB 12014 防靜電工作服
GB/T 20991-2007 個體防護裝備 鞋的測試方法
GB 4385-1995 防靜電鞋、導電鞋技術要求
GB 12158-2006 防止靜電事故通用導則
GB 4655-2003 橡膠工業靜電安全規程
GB/T 1692-2008 硫化橡膠絕緣電阻的測定
GB/T 12703.6-2010 紡織品 靜電性能的評定 第6部分 纖維泄漏電阻
GB 13348-2009 液體石油產品靜電安全規程
GB/T 15738-2008 導電和抗靜電纖維增強塑料電阻率試驗方法
GB/T 18044-2008 地毯 靜電習性評價法 行走試驗
GB/T 18864-2002 硫化橡膠 工業用抗靜電和導電產品電阻極限范圍
GB/T 22042-2008 服裝 防靜電性能 表面電阻率試驗方法
GB/T 22043-2008 服裝 防靜電性能 通過材料的電阻(垂直電阻)試驗方法
GB/T 24249-2009 防靜電潔凈織物
GB 26539-2011 防靜電陶瓷磚 Antistatic ceramic tile
GB/T 26825-2011 抗靜電防腐膠
GB 50515-2010 導(防)靜電地面設計規范
GB 50611-2010 電子工程防靜電設計規范
GJB 105-1998-Z 電子產品防靜電放電控制手冊
GJB 3007A-2009 防靜電工作區技術要求
GJB 5104-2004 無線電引信風帽用防靜電涂料及風帽靜電性能通用要求
技術參數
測試電壓 （V） 10 50 100 250 500 1000
電阻測量范圍 1×104Ω ～1×1018 Ω；
電流測量范圍 2×10-4Ａ ～1×10-16Ａ；
①直流高壓電流輸出 10，50，100，500，1000V 五檔
②根據試樣的電阻值及直流高壓值選擇合適的量程倍率。
③高輸入阻抗直流放大器（輸入阻抗>1015Ω）
④指示儀表，指示被測絕緣電阻。
⑤電源供給儀器各部分工作電源。
安全注意事項
4.1 使用前務必詳閱此說明書，并遵照指示步驟，依次操作。
4.2 請勿使用非原廠提供之附件，以免發生危險。
4.3 進行測試時，本儀器測量端高壓輸出端上有直流高壓輸出，嚴禁人體接觸 ，以免觸電。
4.4 為避免測試棒本身絕緣泄漏造成誤差，接儀器測量端輸入的測試棒應盡可 能懸空，不與外界物體相碰。
4.5 當被測物絕緣電阻值高，且測量出現指針不穩現象時，可將儀器測量線屏 蔽端夾子接上。 例如：對電纜測纜芯與纜殼的絕緣時，除將被測物兩 端分 別接于輸入端與高壓 端，再將電纜殼 ，芯之間的內層絕緣物接儀器 “G”，以消 除因 表面漏電而 引起的測量誤差。也可用加屏蔽盒的方法， 即將被測物置于金屬屏蔽盒內，接上測量線。
優點：
體積小、重量輕、準確度高；
的被測電阻、和流過電阻的電流雙顯示，使操作測量更加方便；
性能穩定、讀數方便；
既能測電阻又能測電流；
使用操作簡便，在任何電阻量程和測試電壓下均直接讀顯示數字結果，免去要乘以一個系數的麻煩，使測量超高電阻就如用萬用表測量普通電阻樣簡便。
Insulation epoxy resin, plastic rubber surface resistivity tester volume conditions of use
1) ambient temperature: 0 ~ 40 ℃
(2) the relative humidity: 70% or less
(3) power supply current, ac 220 v + 10% for 50 hz
Insulation epoxy resin, plastic rubber volume surface resistivity tester is main criteria:
GB/T 1410-2006 of solid insulating materials Volume resistivity and surface resistivity test method
GB1672-8 liquid plasticizer of volume resistivity measurement
GB 12014 anti-static overalls
GB/T 20991-2007 test method of the individual protective equipment of shoes
GB 4385-1995, anti-static shoes, conductive technical requirements
Prevent electrostatic guide general accident of GB 12158-12158
GB 4655-2003 rubber industrial electrostatic safety procedures
GB/T 1692-2008 vulcanized rubber insulation resistance measurement
GB/T 12703.6 2010 textile electrostatic performance evaluation Part 6 fiber leakage resistance
GB 13348-2009 liquid petroleum products electrostatic safety procedures
GB/T 15738-2008, conductive and antistatic fibre reinforced plastics resistivity test method
GB/T 18044-2008 - carpet static walking behavior evaluation test
GB/T 18864-2002 - vulcanized rubber industry with antistatic and conductive products resistance limit range
GB/T 22042-2008 clothing antistatic performance surface resistivity test method
GB/T 22043-2008 clothing antistatic performance by the resistance of the material (vertical resistance) test method
GB/T 24249-2009, anti-static clean fabric
GB 26539-2011 anti-static ceramic tile Antistatic ceramic tile
Anti-static anticorrosion adhesive GB/T 26825-26825
GB 50515-50515 lead (prevention) electrostatic surface design specification
GB 50611-50611 electronic engineering antistatic design specifications
GJB 105-1998 - Z electronic products electrostatic discharge manual control
GJB 3007 a - 2009 anti-static work area technical requirements
GJB 5104-2004 radio fuze cap with antistatic coatings and cowl electrostatic general performance requirements
Insulation epoxy resin, plastic rubber surface resistivity tester size technical parameters
Test voltage (V) 10 to 50, 100, 250, 500, 1000
Resistance measurement range 1 1 x 1018 x 104 Ω ~ Ω;
Current measurement range 2 x 10-4 a ~ 1 x 10 to 16 a.
1) dc,50,100,500,1000 10 V output current high five
(2) according to the sample resistance and dc high voltage value to choose the appropriate range ratio.
(3) high input impedance dc amplifier (> 1015 Ω) the input impedance
(4), indicating meter indicates measured insulation resistance.
(5) power supply instrument parts work power.
Insulation epoxy resin, plastic rubber surface resistivity tester size security considerations
4.1 be sure to read the manual before use and follow the instructions step, operating in turn.
4.2 do not use the original factory to provide the attachment, thank you for your cooperation.
4.3 during the test, the instrument measuring the dc high voltage output high voltage output, it is strictly prohibited to human exposure, so as to avoid electric shock.
4.4 to avoid test bar insulation leakage error caused by itself, by instrument measuring the input can be hung up test bar, no object collision with the outside world.
Analyte 4.5 when a high insulation resistance, and measure the instability phenomenon appear Pointers, line screen can be measured All the clip connected. For example: the insulation of the cable and cable to cable measured shell, in addition to the analyte to the two end points Don't pick up the input and the high pressure side, and then to a shell, the cable core between inner insulation instruments "G", to eliminate the error of measurement caused by surface leakage. Method can also be used with shielding box, is about to be tested on the metal shielding box, measuring line.
Insulation epoxy resin, plastic rubber surface resistivity tester size advantage:
Small volume, light weight, high accuracy;
Unique resistance being measured, according to the current through the resistor, and double make the measurement more convenient operation;
Stable performance, easy reading;
To measure resistance and current measurement;
Use of simple operation, are directly under any resistance range and testing voltage reading display Numbers as a result, the bother of should be multiplied by a coefficient, makes the measuring high resistance as ordinary resistance is measured with a multimeter sample is simple.
您感興趣的產品PRODUCTS YOU ARE INTERESTED IN
儀表網 設計制作，未經允許翻錄必究 .? ? ?
請輸入賬號
請輸入密碼
請輸驗證碼
