無線測溫傳感器 合金片固定安裝 無需電池ATE400可用于3~35kV戶內開關柜，包括中置柜、手車柜、固定柜、環網柜等多種開關柜；也可用于0.4kV低壓柜，包括固定柜，抽屜柜等。無線測溫傳感器可安裝于柜內任何發熱點上，利用無線數據傳輸技術實時發送監測數據，再通過接收裝置將溫度數據傳輸到顯示裝置或者遠程監控系統。
無線測溫傳感器 合金片固定安裝 無需電池ATE400可用于3~35kV戶內開關柜，包括中置柜、手車柜、固定柜、環網柜等多種開關柜；也可用于0.4kV低壓柜，包括固定柜，抽屜柜等。無線測溫傳感器可安裝于柜內任何發熱點上，利用無線數據傳輸技術實時發送監測數據，再通過接收裝置將溫度數據傳輸到顯示裝置或者遠程監控系統。
技術參數
工作電源：CT取電，啟動電流5A
測溫范圍：-50℃~+125℃
測量精度：±1℃
采樣精度：15s
發射頻段：470MHz
傳輸距離：空曠150米
發射周期：15s
適用于靜觸頭，母排，電纜，母排、電纜搭接處等多種場合。
The mini type called ATE400 is suitable for using at moving contacts, bus bars, cables and joints between bus bar and cable.
迷你型無源無線溫度傳感器結構說明：
Mini type passive temperature sensor structure introduction:
1 —— 溫度傳感器主體The core of wireless temperature sensor ATE400
2 —— 合金底座，與溫度探頭接觸alloy bottom, touched with temperature probe
3 —— 鎖扣，用于固定合金片metal hasp, for fixing alloy chip
4 —— 取電合金片，用于感應取電alloy chip, for CT-powered
5 —— 硅膠墊片，用于支撐合金片silicone gasket, used to support the alloy chip
6 —— 合金片安裝孔，用于安裝合金片alloy chip hole, used to install the alloy chip
取2根合金片穿過鎖緊件安裝孔，將合金片居中對折后鎖緊件固定在折彎處；將對折后的4層合金片分別穿過硅膠墊片-傳感器主體-硅膠墊片；將整體傳感器環繞安裝部位一圈后拉緊合金片并旋緊螺絲；合金片多余部分留取適當長度并折疊壓緊。合金片安裝示意過程如下：
注：ATE400可安裝靜觸頭，銅排，電纜頭; 如需安裝動觸頭，需要考慮梅花頭及套筒高度是否足夠。
Firstly, take 2 pieces of alloy chips through the mounting hole of metal hasp, meanwhile fold the alloy chips and fix the metal hasp in the middle of alloy chips. Secondly, take the folded alloy chips through one silicone gasket, the core of ATE400 and another silicone gasket in turn.Thirdly, circle the whole alloy chips around the mounting position and tension the alloy chips, then tighten the screw on the metal hasp. Finally, subtract the excess alloy chips. The complete installation process is shown in Figures 1 to 4.
Note: ATE400 can be installed with fixed contact, copper plate and cable head; If it is necessary to install moving contacts, it is necessary to consider whether the height of plum blossom head and sleeve is sufficient.
