產品介紹
KSD314系列突跳式溫控器（碟片直徑3/4英寸）是帶外殼的雙金屬片溫控器，工作于阻性負載下。其負載能力高，大額定電流為35A。適合用于大功率的電器中作溫度控制或過熱保護之用。
| 產品參數 技術參數 | |||||
| 子系列 | 動作類型 | 開關結構 | 額定值 | OT | 壽命次數 |
| Max. OT | Life cycles | ||||
| KSD314-T | 斷電復位 | SPST（單刀單擲）、 | 250V 35A | 140°C | 一萬 |
| （電壓保持型） | 常閉 | 125V 35A | |||
| 耐熱溫度 Tmax（單位 units: C） | |||||
| 不同OT下的耐熱溫度 Tamx. of various OT | |||||
| OT≤30 | OT:31～70 | OT:71～120 | OT:121～180 | ||
| 100(L) | 140(L) | 205(L) | 205(L) | —— | |
| 130(S) | 170(S) | 235(S) | 235(S) | ||
L：* Long term
S：小于15分鐘 Less than 15 min
安裝與使用
使用中2安裝與使用說明：
1．接地方式：通過溫控器金屬外蓋與設備接地金屬部件相連
Method of earth: By means of the metal cup of thermostat connected in the earthing metal part.
2．溫控器應工作于空氣相對濕度不大于90%、無腐蝕性氣、可燃性氣體和導電塵埃存在的一般室內環境。
The thermostat should work in environment with humidity not higher than 90%, free of caustic, flammable gas and conducting dust.
3．溫控器采用接觸感溫時，應使其封蓋緊貼被控器具的發熱部位，并應在封蓋感溫表面涂上導熱硅脂或其他性能類似的導熱介質。
When the thermostat is used to sense the temperature of solid items, its cover should be clung to the heating part of such items. Meanwhile, heat-conducting silicon grease, or other heat media of similar nature, should be applied to the cover’s surface.
4．溫控器通過接觸液體或蒸汽感溫時，建議采用不銹鋼封蓋的產品，并應有可靠的防漏措施，以免液體滲到溫控器絕緣部件上。
If the thermostat is used to sense the temperature of liquids or steam, it is strongly recommended to adopt a version with stainless-steeled cup. Moreover, cautious measures should be taken to prevent liquids getting into/onto the thermostat’s insulation parts.
5．不可把封蓋頂部壓塌或使其變形，以免動作溫度改變或影響其他性能。
The top of the cup must not be pressed to sink, so as to avoid adverse effect on the thermostat’s temperature sensitivity or its other functions.
6．不得讓液體滲入溫控器內部！殼體必須避免受到過大的力以防止出現裂紋；殼體應保持清潔，防止導電物質污染，以免因絕緣性能降低而發生短路擊穿。
Liquids must be kept out of the thermostat’s inner part! The base must avid any force that could lead to crack; it should be kept clear and away from the pollution of electric substance to prevent insulation weakening that leads to short-circuited damages.
7．使用過程不能折彎接線端子，否則將影響電氣連接的可靠性。
The terminals should be bent, or else, the reliability of electric connection will be influenced. cracking base, distorted terminal and wire lead coming off.
