PND176石油產品凝點、傾點測定儀
該石油產品傾點凝點測定器是引進*生產的，符合GB/T 510。該儀器采用壓縮機制冷原理，封閉式浴槽，配有傾斜支架及傾點套，并裝有智能數字顯示控制儀，使用方便、質量可靠，該儀器采用模糊控制原理和PID自整定技術，控制性能穩定可靠，是化驗室的試驗儀器。
該儀器制冷系統是由壓縮機、過濾器、毛細管節流器、蒸發器及各連接管路組成。制冷劑通過蒸發器吸熱膨脹，膨脹后的氣體由壓縮機壓入排氣管路形成高溫高壓氣體再進入冷凝器冷卻成液體，然后經毛細管節流降壓進入蒸發器蒸發吸熱從而達到制冷目的。制冷劑蒸發后又被壓縮機壓入排氣管進入冷凝器，這樣周而復始地工作實現循環制冷。溫度控制系統是由智能數顯控溫儀進行PID調節實現定點控溫，控溫儀輸出的控制信號觸發固態繼電器，使加熱管工作抵消壓縮機制冷系統產生的冷量，使其恒在我們所需要的溫度上。
該儀器制冷系統是由壓縮機、過濾器、毛細管節流器、蒸發器及各連接管路組成。制冷劑通過蒸發器吸熱膨脹，膨脹后的氣體由壓縮機壓入排氣管路形成高溫高壓氣體再進入冷凝器冷卻成液體，然后經毛細管節流降壓進入蒸發器蒸發吸熱從而達到制冷目的。制冷劑蒸發后又被壓縮機壓入排氣管進入冷凝器，這樣周而復始地工作實現循環制冷。溫度控制系統是由智能數顯控溫儀進行PID調節實現定點控溫，控溫儀輸出的控制信號觸發固態繼電器，使加熱管工作抵消壓縮機制冷系統產生的冷量，使其恒在我們所需要的溫度上。
技術指標 ：
制冷溫度 ：室溫～-45℃(可選－75℃液晶顯示)
降溫時間 ：≤100分鐘
輸入方式 ：Pt100
控溫精度 ：±0.1℃
電源電壓 ：AC220V 50Hz
結構形式 ：一槽兩孔
制冷溫度 ：室溫～-45℃(可選－75℃液晶顯示)
降溫時間 ：≤100分鐘
輸入方式 ：Pt100
控溫精度 ：±0.1℃
電源電壓 ：AC220V 50Hz
結構形式 ：一槽兩孔
PND176 petroleum products pour point analyzer
The determination of the pour point of the pour point of the petroleum products is produced by the introduction of advanced technology from Japan, according to GB / T 510. The instrument uses a compressor refrigeration principle, enclosed bath with tilt stａnd and pour point sets, and is equipped with intelligent digital display controller, easy to use, reliable quality, the instrument uses fuzzy control principle and PID self-tuning technology, control performance stable and reliable, is the the laboratory preferred test instrument.
The refrigeration system is the instrument by the compressor, filter, capillary restrictor, connected to the evaporator and the piping components. Endotherm of the refrigerant through the evaporator expansion pressure by the compressor, the expansion of the gas after the formation of high temperature and high pressure gas into the exhaust pipe and then into the condenser cooling into liquid, and then by capillary throttling into the evaporator evaporation endothermic to achieve refrigeration purposes . Compressor pressure refrigerant evaporates then into the exhaust pipe into the condenser, so the cycle refrigeration cycle to work. The temperature control system is noticeable by the intelligent digital temperature control device PID adjustment to achieve the fixed-point temperature control, temperature control device output control signal to trigger solid-state relays, heating pipe work offset compressor refrigeration system to produce cold it constant in on the required temperature.
Technical indicators:
Refrigeration temperature: room temperature ~ -75 ℃
Cooling time: ≤ 100 minutes
Input mode: Pt100
Temperature control accuracy: ± 0.1 ℃
Power supply voltage: AC220V 50Hz
Structural forms: a slot two holes
The determination of the pour point of the pour point of the petroleum products is produced by the introduction of advanced technology from Japan, according to GB / T 510. The instrument uses a compressor refrigeration principle, enclosed bath with tilt stａnd and pour point sets, and is equipped with intelligent digital display controller, easy to use, reliable quality, the instrument uses fuzzy control principle and PID self-tuning technology, control performance stable and reliable, is the the laboratory preferred test instrument.
The refrigeration system is the instrument by the compressor, filter, capillary restrictor, connected to the evaporator and the piping components. Endotherm of the refrigerant through the evaporator expansion pressure by the compressor, the expansion of the gas after the formation of high temperature and high pressure gas into the exhaust pipe and then into the condenser cooling into liquid, and then by capillary throttling into the evaporator evaporation endothermic to achieve refrigeration purposes . Compressor pressure refrigerant evaporates then into the exhaust pipe into the condenser, so the cycle refrigeration cycle to work. The temperature control system is noticeable by the intelligent digital temperature control device PID adjustment to achieve the fixed-point temperature control, temperature control device output control signal to trigger solid-state relays, heating pipe work offset compressor refrigeration system to produce cold it constant in on the required temperature.
Technical indicators:
Refrigeration temperature: room temperature ~ -75 ℃
Cooling time: ≤ 100 minutes
Input mode: Pt100
Temperature control accuracy: ± 0.1 ℃
Power supply voltage: AC220V 50Hz
Structural forms: a slot two holes
